View N150P2-L06_4615595.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

customer?s acceptance specification february 4, 2004 casi-N150P2-L06-fu01 1/34 to: accepted by: date: customer's acceptance specification type 15.0 sxga+ color tft/lcd module model name: N150P2-L06 document control number: cas i-N150P2-L06-fu01 issued by: m. suzuki date: february 4, 2004 sales support international display technology www.datasheet.net/ datasheet pdf - http://www..co.kr/
customer?s acceptance specification february 4, 2004 casi-N150P2-L06-fu01 2/34 i contents i contents ii record of revision 1.0 handling precautions 2.0 general description 2.1 characteristics 2.2 functional block diagram 3.0 absolute maximum ratings 4.0 optical characteristics 4.1 luminance uniformity 5.0 signal interface 5.1 connectors 5.2 interface signal connector 5.3 interface signal description 5.3.1 e-edid 5.4 interface signal electrical characteristics 5.4.1 signal electrical characteristics for lvds receiver 5.4.2 lvds receiver internal circuit 5.4.3 recommended guidelines for motherboard pcb design and cable selection 5.5 inverter signal connector 5.6 inverter signal description 5.7 inverter signal electrical characteristics 6.0 pixel format image 7.0 parameter guide line for cfl inverter 8.0 interface timings 8.1 timing characteristics 8.2 timing definition 9.0 power consumption 10.0 power on/off sequence 11.0 mechanical characteristics 12.0 national test lab requirement 13.0 qualifications and cfl life 13.1 visual screen quality 13.2 line defect 13.3 bright and black dots 13.4 cfl life 14.0 packaging specification 15.0 label www.datasheet.net/ datasheet pdf - http://www..co.kr/
customer?s acceptance specification february 4, 2004 casi-N150P2-L06-fu01 3/34 ii record of revision date document revision page summary february 4, 2004 cas i-N150P2-L06-fu01 all first edition for fujitsu limited. www.datasheet.net/ datasheet pdf - http://www..co.kr/
customer?s acceptance specification february 4, 2004 casi-N150P2-L06-fu01 4/34 1.0 handling precautions ? if any signals or power lines deviate from the power on/off sequence, it may cause shorten the life of the lcd module. ? the lcd panel and the cfl are made of glass and may break or crack if dropped on a hard surface, so please handle them with care. ? cmos ics are included in the lcd panel. they should be handled with care, to prevent electrostatic discharge. ? do not press the reflector sheet at the back of the lcd module to any directions. ? do not stick the adhesive tape on the reflector sheet at the back of the lcd module. ? please handle with care when mount in the system cover. mechanical damage for lamp reflector ,for lamp cable and for lamp connector may cause safety problems. ? small amount of materials having no flammability grade is used in the lcd module. the lcd module should be supplied by power complied with requirements of limited power source (2.5, iec60950 or ul60950), or be applied exemption conditions of flammability requirements (4.7.3.4, iec60950 or ul60950) in an end product. ? the lcd module is designed so that the cfl in it is supplied by limited current circuit (2.4, iec60950 or ul60950). ? the fluorescent lamp in the liquid crystal display(lcd) contains mercury. do not put it in trash that is disposed of in landfills. dispose of it as required by local ordinances or regulations. ? never apply detergent or other liquid directly to the screen. ? wipe off water drop immediately. long contact with water may cause discoloration or spots. ? when the panel surface is soiled, wipe it with absorbent cotton or other soft cloth; do not use solvents or abrasives. ? do not touch the front screen surface in your system, even bezel. ? gently wipe the covers and the screen with a soft cloth. ? the information contained herein is presented only as a guide for the applications of our products. no responsibility is assumed by international display technology for any infringements of patents or other right of the third partied which may result from its use. no license is granted by implication or otherwise under any patent or patent rights of international display technology or others. www.datasheet.net/ datasheet pdf - http://www..co.kr/
customer?s acceptance specification february 4, 2004 casi-N150P2-L06-fu01 5/34 2.0 general description this specification applies to the type 15.0 color tft/lcd module 'N150P2-L06. this module is designed for a display unit of a notebook style personal computer. the screen format and electrical interface are intended to support the sxga+ (1400(h) x 1050(v)) screen. support color is native 262k colors ( rgb 6-bit data driver ). all input signals are lvds (low voltage differential signaling) interface compatible. this module does not contain an inverter card for backlight. 2.1 characteristics the following items are characteristics summary on the table under 25 degree c c ondition: characteristics items specifications screen diagonal [mm] 381 pixels h x v 1400(x3) x 1050 active area [mm] 304.5(h) x 228.375(v) pixel pitch [mm] 0.2175(per one triad) x 0.2175 pixel arrangement r,g,b vertical stripe weight [grams] 590 max. physical size [mm] 317.3(w) x 242.0(h) x 6.2(d) typ./6.5(d) max. display mode normally white support color native 262k colors (rgb 6-bit data driver) white luminance [cd/m 2 ] design point 2:(icfl=6.5ma) 200 typ.(center), 185 typ.(5 points average) contrast ratio 250 : 1 typ. surface treatment anti-glare treatment optical rise time/fall time [msec] 45 typ.,50 max. nominal input voltage vdd [volt] +3.3 typ. power consumption [watt] design point 2:(icfl=6.5ma) backlight : 4.1 typ., 4.7 max. logic : 1.4 typ., 2.6 max. electrical interface 8 pairs lvds (even/odd r/g/b eedid (clock, data) data (6bit), 3sync signals, clock) cfl cable length [mm] 105 typ. temperature range [degree c] operating storage (shipping) 0 to +50 -20 to +60 www.datasheet.net/ datasheet pdf - http://www..co.kr/
customer?s acceptance specification february 4, 2004 casi-N150P2-L06-fu01 6/34 2.2 functional block diagram the following diagram shows the functional block of this type 15.0 color tft/lcd module. the first lvds port transmits even pixels while the second lvds port transmits odd pixels. j a e f i - x b 3 0 s l - h f 1 0 ( 3 0 p i n , l o c k t y p e ) x-driver tft array/cell 6bit color data for r/g/b dtclk(even/odd) dsptmg hsync vsync vdd lcd controller lcd drive card backlight unit 1400(r/g/b) x 1050 gnd dc-dc converter ref circuit (even/ odd) < 8 pairs lvds > even pixel odd pixel dual lvds receiver lcd-drive connector y-driver g/a eedid chip veedid clkeedid dataeedid bhsr-02vs-1 (jst) ccfl high voltate ccfl low voltage ccfl connector www.datasheet.net/ datasheet pdf - http://www..co.kr/
customer?s acceptance specification february 4, 2004 casi-N150P2-L06-fu01 7/34 3.0 absolute maximum ratings absolute maximum ratings of the module is as follows: item symbol min max unit conditions supply voltage vdd -0.3 +4.0 v input voltage of signal other inputs -0.3 vdd+0.3 v lamp ignition voltage vcfl - +1,650 vrms ta = 0 [deg.c] cfl current icfl - 7 marms cfl peak inrush current icflp - 20 marms ta = 25 [deg.c] (note 1) operating temperature top 0 +50 deg.c (note 2) operating relative humidity hop 8 95 %rh (note 2) storage temperature tst -20 +60 deg.c (note 2) storage relative humidity hst 5 95 %rh (note 2) vibration 1.5 10-200 g hz shock 50 18 g ms rectangle wave note: 1. duration: 50 [msec] max. 2. maximum wet-bulb should be 39 degree c and no condensation. www.datasheet.net/ datasheet pdf - http://www..co.kr/
customer?s acceptance specification february 4, 2004 casi-N150P2-L06-fu01 8/34 4.0 optical characteristics the optical characteristics are measured under stable conditions as follows under 25 degree c condition: item conditions specification typ. note viewing angle (degrees) horizontal (right) k> 10 (left) 40 min. 40 min. - - k: contrast ratio vertical (upper) k> 10 (lower) 15 min. 30 min. - - contrast ratio 250 200 min. rising 45 50 max. response time (ms) falling 45 50 max. color red x 0.577 + 0.030 chromaticity red y 0.338 + 0.030 (cie) green x 0.310 + 0.030 green y 0.554 + 0.030 blue x 0.158 + 0.030 blue y 0.124 + 0.030 white x 0.313 + 0.030 white y 0.329 + 0.030 white luminance (cd/m 2 ) icfl 6.5 ma 200 typ. center 185 typ. 5.points average www.datasheet.net/ datasheet pdf - http://www..co.kr/
customer?s acceptance specification february 4, 2004 casi-N150P2-L06-fu01 9/34 the following is the note for the optical characteristics: ? chromaticity and white balance are defined as the c.i.e. 1931 x,y coordinates at the center of lcd. the measurement equipment are as shown below table. item measuring equipment viewing angle mcpd-7000 by ohtsuka elec contrast mcpd-7000 by ohtsuka elec response time bm5a by topcon optical co.,ltd. white luminance mcpd-7000 by ohtsuka elec luminance uniformity mcpd-7000 by ohtsuka elec chromaticity mcpd-7000 by ohtsuka elec white balance mcpd-7000 by ohtsuka elec the measurement is to be done after 30 minutes of power-on of backlight. unless otherwise specified, the ambient conditions are as following. ambient temperature : 25 + 2 ( degreec ) ambient humidity : 25 - 85 ( % ) atmospheric pressure : 86.0 - 104.0 ( kpa ) x y z left right low er upper center of lcd (x =0,y =0,z =0) viewing or m easuring direction viewing or measuring direction +h -v www.datasheet.net/ datasheet pdf - http://www..co.kr/
customer?s acceptance specification february 4, 2004 casi-N150P2-L06-fu01 10/34 4.1 luminance uniformity when the backlight is on with all pels in the unselected state (white), the luminance uniformity is defined as follows; average luminance is defined as follows. l1 + l2 + l3 + l4 + l5 average luminance = 5 luminance variation is measured by dividing the maximum luminance values of the 13 or 5 test points by the minimum luminance of the 13 or 5 test points. minimum luminance 13 points (l1-l13) luminance uniformity > 1.65 maximum luminance 13 points (l1-l13) minimum luminance 5 points (l1-l5) luminance uniformity > 1.25 maximum luminance 5 points (l1-l5) average luminance and luminance uniformity test points l1 l2 l3 l4 l5 263 525 787 350 700 1050 l6 l7 l8 l9 l11 l12 l13 l10 10mm 10mm 10mm 10mm www.datasheet.net/ datasheet pdf - http://www..co.kr/
customer?s acceptance specification february 4, 2004 casi-N150P2-L06-fu01 11/34 5.0 signal interface 5.1 connectors physical interface is described as for the connector on module. these connectors are capable of accommodating the following signals and will be following components. connector name / designation for signal connector manufacturer jae type / part number fi-xb30sl-hf10 mating receptacle manufacture jae mating receptacle/part number fi-x30m, fi-x30c2l connector name / designation for lamp connector manufacturer jst type / part number bhsr-02vs-1 mating type / part number sm02b-bhss-1 www.datasheet.net/ datasheet pdf - http://www..co.kr/
customer?s acceptance specification february 4, 2004 casi-N150P2-L06-fu01 12/34 5.2 interface signal connector pin # signal name pin # signal name 1 gnd 16 gnd 2 vdd 17 reclkin- 3 vdd 18 reclkin+ 4 v eedid (note 2,3) 19 gnd 5 reserved (note 1) 20 roin0- 6 clk eedid (note 2,4) 21 roin0+ 7 data eedid (note 2,4) 22 gnd 8 rein0- 23 roin1- 9 rein0+ 24 roin1+ 10 gnd 25 gnd 11 rein1- 26 roin2- 12 rein1+ 27 roin2+ 13 gnd 28 gnd 14 rein2- 29 roclkin- 15 rein2+ 30 roclkin+ note: 1. 'reserved' pins are not allowed to connect any other line. 2. this lcd module complies with "vesa enhanced extended display identification data standard release a, revision 1" and supports "eedid version 1.3". 3. v eedid power source shall be the limited current circuit which has not exceeding 1a. (reference document : "enhanced display data channel (e-ddc tm ) proposed standard", vesa) 4. both clk eedid line and data eedid line are pulled up with 10k ohm resistor to v eedid power source line at lcd panel, respectively. www.datasheet.net/ datasheet pdf - http://www..co.kr/
customer?s acceptance specification february 4, 2004 casi-N150P2-L06-fu01 13/34 5.3 interface signal description lcd drive connector signal description signal name description dual lvds mode rein0+, rein0- even lvds differential data input (red0-red5, green0) rein1+, rein1- even lvds differential data input (green1-green5,blue0-blue1) rein2+, rein2- even lvds differential data input (blue2-blue5, hsync, vsync, dsptmg) reclkin+, reclkin- even lvds differential clock input roin0+, roin0- odd lvds differential data input (red0-red5, green0) roin1+, roin1- odd lvds differential data input (green1-green5, blue0-blue1) roin2+, roin2- odd lvds differential data input (blue2-blue5, hsync, vsync, dsptmg) roclkin+, roclkin- odd lvds differential clock input vdd +3.3v power supply gnd ground note : input signals shall be low or hi-z state when vdd is off www.datasheet.net/ datasheet pdf - http://www..co.kr/
customer?s acceptance specification february 4, 2004 casi-N150P2-L06-fu01 14/34 signal name description +red 5 (er5/or5) red data 5 (msb) +red 4 (er4/or4) red data 4 +red 3 (er3/or3) red data 3 +red 2 (er2/or2) red data 2 +red 1 (er1/or1) red data 1 +red 0 (er0/or0) red data 0 (lsb) (even/odd) red-pixel data: each red pixel's brightness data consists of these 6 bits pixel data. +green 5 (eg5/og5) green data 5 (msb) +green 4 (eg4/og4) green data 4 +green 3 (eg3/og3) green data 3 +green 2 (eg2/og2) green data 2 +green 1 (eg1/og1) green data 1 +green 0 (eg0/og0) green data 0 (lsb) (even/odd) green-pixel data: each green pixel's brightness data consists of these 6 bits pixel data. +blue 5 (eb5/ob5) blue data 5 (msb) +blue 4 (eb4/ob4) blue data 4 +blue 3 (eb3/ob3) blue data 3 +blue 2 (eb2/ob2) blue data 2 +blue 1 (eb1/ob1) blue data 1 +blue 0 (eb0/ob0) blue data 0 (lsb) (even/odd) blue-pixel data: each blue pixel's brightness data consists of these 6 bits pixel data. dtclk data clock: the typical frequency is 81mhz. (even/odd) the signal is used to strobe the pixel +data and the +dsptmg +dsptmg (dsp) when the signal is high, the pixel data shall be valid to be displayed. vsync (v-s) vertical sync: this signal is synchronized with dtclk. only active high signal is acceptable. hsync (h-s) horizontal sync: this signal is synchronized with dtclk. both active high/low signals are acceptable. vdd power supply gnd ground v eedid eedid 3.3v power supply clk edid eedid clock data eedid eedid data note: output signals except v eedid ,clk eedid and data eedid from any system shall be hi-z state when vdd is off. vsync should start with active high ( positive pulse ) signal from when vdd is supplied and its polarity should not be changed. www.datasheet.net/ datasheet pdf - http://www..co.kr/
customer?s acceptance specification february 4, 2004 casi-N150P2-L06-fu01 15/34 5.3.1 e-edid e-edid detail in this lcd module is in the following table address (hex) description data (hex) remark 00 - 07 header 00 ff ff ff ff ff ff 00 header, fixed 08 - 09 id manufacturer name 24 94 "idt" 0a - 0b id product code 02 00 product code 0c - 0f id serial number 00 00 00 00 unused 10 week of manufacture 00 unused 11 year of manufacture 00 unused 12 - 13 edid structure version / revision 01 03 ver1.3 14 - 18 basic display parameter / features 80 1e 17 78 0a active area : 30.45cm x 22.84cm,gamma : 2.2 19 - 22 color characteristics (note 1) 23 - 25 established timing 00 00 00 unused 26 - 35 standard timing identification 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 unused 36 - 47 detailed timing / monitor description #1 30 2a 78 f0 50 1a 0f 40 30 70 13 00 31 e4 10 00 00 1e typical timing 48 - 59 detailed timing / monitor description #2 (note 1) 5a - 6b detailed timing / monitor description #3 00 00 00 fe 00 49 44 54 0a 20 20 20 20 20 20 20 20 20 manufactuerer name "idt" 6c - 7d detailed timing / monitor description #4 00 00 00 fe 00 4e 31 35 30 50 32 0a 20 20 20 20 20 20 manufacturer p/n "n150p2" 7e extension flag 00 no extension 7f checksum (note 1) note1: detail data contents shall be determined with concurrence between user and international display technology (idtech). www.datasheet.net/ datasheet pdf - http://www..co.kr/
customer?s acceptance specification february 4, 2004 casi-N150P2-L06-fu01 16/34 5.4 interface signal electrical characteristics 5.4.1 signal electrical characteristics for lvds receiver table. electrical characteristics parameter symbol min typ max unit conditions differential input high threshold vth +100 mv differential input low threshold vtl -100 mv magnitude differential input voltage |vid| 100 600 mv common mode voltage vcm 1.125 1.5 v common mode voltage offset ? vcm -50 +50 mv note: ? input signals shall be low or hi-z state when vdd is off. figure. voltage definitions www.datasheet.net/ datasheet pdf - http://www..co.kr/
customer?s acceptance specification february 4, 2004 casi-N150P2-L06-fu01 17/34 table. switching characteristics parameter symbol min typ max unit conditions clock frequency fc 51 54 57 mhz cycle time tc 17.5 18.5 19.6 ns data setup time tsu 700 ps fc = 54mhz, jitter < 50ps data hold time thd 700 ps cycle modulation rate (note) tcjavg 20 ps/clk note: this specification defines maximum average cycle modulation rate in peak-to-peak transition within any 100 clock cycles. this specification is applied only if input clock peak jitter within any 100 clock cycles is greater than 300ps. figure. timing definition (even) www.datasheet.net/ datasheet pdf - http://www..co.kr/
customer?s acceptance specification february 4, 2004 casi-N150P2-L06-fu01 18/34 figure. timing definition (odd) www.datasheet.net/ datasheet pdf - http://www..co.kr/
customer?s acceptance specification february 4, 2004 casi-N150P2-L06-fu01 19/34 figure. timing definition (detail a) www.datasheet.net/ datasheet pdf - http://www..co.kr/
customer?s acceptance specification february 4, 2004 casi-N150P2-L06-fu01 20/34 5.4.2 lvds receiver internal circuit below figure shows the internal block diagram of the lvds receiver. 5.4.3 recommended guidelines for motherboard pcb design and cable selection following the suggestions below will help to achieve optimal results. ? use controlled impedance media for lvds signals. they should have a matched differential impedance of 100ohm. ? match electrical lengths between traces to minimize signal skew. ? isolate ttl signals from lvds signals. ? for cables, twisted pair, twinax, or flex circuit with close-coupled differential traces is recommended. www.datasheet.net/ datasheet pdf - http://www..co.kr/
customer?s acceptance specification february 4, 2004 casi-N150P2-L06-fu01 21/34 5.5 signal for lamp connector pin # signal name 1 lamp high voltage 2 lamp low voltage 6.0 pixel format image following figure shows the relationship of the input signals and lcd pixel format image. even and odd pair of rgb data are sampled at a time. r g b r g b r g b r g b r g b r g b r g b r g b even odd even odd 0 1 1399 1st line 1050th line 1398 www.datasheet.net/ datasheet pdf - http://www..co.kr/
customer?s acceptance specification february 4, 2004 casi-N150P2-L06-fu01 22/34 7.0 parameter guide line for cfl inverter parameter min dp max units condition white luminance (center) (5 points average) 180 165 200 185 - - cd/m 2 (ta=25 deg.c) (icfl=6.5marms) cfl current (icfl) 3.0 6.5 7.0 marms (ta=25 deg.c) cfl frequency (fcfl) 40 60 khz (ta=25 deg.c) note 1 cfl ignition voltage (vs) 1,500 - - vrms (ta= 0 deg.c) note 3 cfl voltage (reference)(vcfl) - 630 - vrms (ta=25 deg.c) note 2 cfl power consumption (pcfl) - 4.1 - w (ta=25 deg.c) note 2 note 1: cfl discharge frequency should be carefully determined to avoid interference between inverter and tft lcd. note 2: calculated value for reference (icfl x vcfl = pcfl). note 3: cfl inverter should be able to give out a power that has a generating capacity of over 1,500 voltage.lamp units need 1,500 voltage minimum for ignition. note 4: dp is recommended design points. *1 all of characteristics listed are measured under the condition using the test inverter. *2 in case of using an inverter other than listed, it is recommended to check the inverter carefully. sometimes, interfering noise stripes appear on the screen, and substandard luminance or flicker at low power may happen. *3 in designing an inverter, it is suggested to check safety circuit very carefully. impedance of cfl, for instance, becomes more than 1 [m ohm] when cfl is damaged. *4 generally, cfl has some amount of delay time after applying kick-off voltage. it is recommended to keep on applying kick-off voltage for 1 [sec] until discharge. *5 cfl discharge frequency must be carefully chosen so as not to produce interfering noise stripes on the screen. *6 reducing cfl current increases cfl discharge voltage and generally increases cfl discharge frequency. so all the parameters of an inverter should be carefully designed so as not to produce too much leakage current from high-voltage output of the inverter. *7 it should be employed the inverter which has 'duty dimming', if icfl is less than 4[ma]. www.datasheet.net/ datasheet pdf - http://www..co.kr/
customer?s acceptance specification february 4, 2004 casi-N150P2-L06-fu01 23/34 the following chart is luminance versus lamp current for your reference. tbd www.datasheet.net/ datasheet pdf - http://www..co.kr/
customer?s acceptance specification february 4, 2004 casi-N150P2-L06-fu01 24/34 8.0 interface timings basically, interface timings described here is not actual input timing of lcd module but output timing of sn75lvds86 (texas instruments) or equivalent. 8.1 timing characteristics signal item symbol min. typ. max. unit fdck 51 54 57 [mhz] dtclk freqency tck 18.5 [ns] fv 60 [hz] tv 16.67 [ms] frame rate nv 1058 1066 2046 [lines] tva 15.78 46.7 [us] v-active level nva 1 3 62 [lines] v-back porch nvb 6 12 125 [lines] +v-sync v-front porch nvf 1 1 [lines] +dsptmg v-line m 1050 [lines] fh 63.98 [khz] th 15.63 [usec] scan rate nh 762 844 1023 [tck] tha 1.037 [usec] h-active level tha 8 56 250 [tck] h-back porch thb 26 64 300 [tck] +h-sync h-front porch thf 8 24 [tck] +dsptmg display thd 12.96 [usec] +data data even/odd n 1400 [dots] note: both positive hsync and positive vsync polarity is recommended www.datasheet.net/ datasheet pdf - http://www..co.kr/
customer?s acceptance specification february 4, 2004 casi-N150P2-L06-fu01 25/34 8.2 timing definition vertical timing support mode tvblk vertical blanking m active field tvf vsync front porch tv,nv frame time tva vsync width tvb vsync back porch 1400 x 1050 at 60hz (h line rate : 15.63 us) 0.250 ms (16 lines) 16.411 ms (1050 lines) 0.016 ms (1 line) 16.661 ms (1066 lines) 0.047 ms (3 lines) 0.188 ms (12 lines) tvblk m tvf tva tvb tv dsptmg -vsync +vsync horizontal timing support mode thblk horizontal blanking thd active field thf hsync front porch th,nh h line time tha hsync width thb hsync back porch 1400 x 1050 dotclock : 108.000 mhz (54.000mhz x2) 2.667 us (288 dots) 12.963 us (1400 dots) 0.444 us (48 dots) 15.630 us (1688 dots) 1.037 us (112 dots) 1.185 us (128 dots) thblk thd thf tha thb th dsptmg -hsync +hsync 02 4 n-4 n-2 video(even) video(odd) video(even) video(odd) dtclk 13 5 n-3 n-1 tck www.datasheet.net/ datasheet pdf - http://www..co.kr/
customer?s acceptance specification february 4, 2004 casi-N150P2-L06-fu01 26/34 9.0 power consumption input power specifications are as follows; symbol parameter min typ max units condition vdd logic/lcd drive voltage 3 3.3 3.6 v load capacitance 40uf pdd vdd power max 2.6 w max pattern vdd=3.6v pdd vdd power 1.4 w all black pattern vdd=3.3v idd max idd current max 720 ma max pattern vdd=3.6v idd idd current 420 ma all black pattern vdd=3.3v vddrp allowable logic/lcd drive ripple voltage 100 mvp-p vddns allowable logic/lcd drive ripple noise 100 mvp-p note: max pattern:2 dot vertical sub-pixel stripe. www.datasheet.net/ datasheet pdf - http://www..co.kr/
customer?s acceptance specification february 4, 2004 casi-N150P2-L06-fu01 27/34 10.0 power on/off sequence vdd power and lamp on/off sequence is as follows. interface signals are also shown in the chart. signals from any system shall be hi-z state or low level when vdd is off. 90% 10% 10% 10% 90% 10ms max. 0 min. 0 v 0 v vdd signals 180ms min. 0 min. 10% 10% 150ms min. 100ms min. 20ms min. lamp 90% 90% on (recommended). www.datasheet.net/ datasheet pdf - http://www..co.kr/
customer?s acceptance specification february 4, 2004 casi-N150P2-L06-fu01 28/34 11.0 mechanical characteristics refer to the attached drawing. www.datasheet.net/ datasheet pdf - http://www..co.kr/
customer?s acceptance specification february 4, 2004 casi-N150P2-L06-fu01 29/34 12.0 national test lab requirement the display module is authorized to apply the ul recognized mark. conditions of acceptability conditions of acceptability - when installed in the end-product, consideration shall be given to the following; 1. this component has been judged on the basis of the required spacings in the standard for safety of information technology equipment, csa/ ul60950, third edition, dated december 1, 2000, sub-clause 2.10, which would cover the component itself if submitted for listing. 2. the unit is intended to be supplied by selv and limited power source. also separated from electrical parts, which may produce high temperature that could cause ignition by as least 13 mm of air or by a solid barrier of material of v-1 minimum. 3. the terminals and connectors are suitable for factory wiring only. 4. a suitable electrical enclosure shall be provided. www.datasheet.net/ datasheet pdf - http://www..co.kr/
customer?s acceptance specification february 4, 2004 casi-N150P2-L06-fu01 30/34 13.0 qualifications and cfl life this quality specification is for the sxga+ tft-lcd module N150P2-L06supplied from international display technology to the customer. please pay attention the following items, when this lcd module is checked in your inspection. 1. you should consider the lcd module to mount that uneven force is not applied to this lcd module. 2. do not push and put a label on the rear side that is located backlight. 3. do not joggle the lcd module, there will be some ripple on the screen. 4. display qualifications depend on the power on time. the visual screen quality is applied the state since 30 seconds after power on 13.1 visual screen quality the following table describes the visual screen quality of the general tft-lcd module. polarizer scratch/bubble size (mm) allowable maximum counts elliptical defects d < 0.15 disregarded 0.15 < d < 0.3 4 0.3 < d 0 linear defects w < 0.05 disregarded 0.05 < w < 0.07 and i < 2.0 4 0.07 < w or 2.0 < l 0 d : diameter longaxis + shortaxis d= 2 w : line width l : line length 13.2 line defect no visible line defect is allowed in entire screen. a line defect is defined as a horizontal and vertical apparent line, visible through 5% nd-filter, that differs from adjacent lines at any gray raster pattern. www.datasheet.net/ datasheet pdf - http://www..co.kr/
customer?s acceptance specification february 4, 2004 casi-N150P2-L06-fu01 31/34 13.3 bright and black dots the following table describes the specification of bright and black dots in the visual screen quality of the tft-lcd module at power-on. items specification any bright dots bright and black dots (total) 6 max 15 max definitions: 1. a bright dot is any one of stuck red, green or blue pixel visible through 5% nd-filter under all black background. 2. a black dot is an unlit sub pixel under any of white, red, green or blue bright raster. basic conditions: viewing distance 350 to 500 mm ambient illumination 300 to 700 lux ambient temperature 20 to 25 degreec 13.4 cfl life cfl life time 10,000 hours condition 25 degree c and 6.5 marms the assumed cfl life will be until the luminance becomes 50% of it's initial value of the panel. www.datasheet.net/ datasheet pdf - http://www..co.kr/
customer?s acceptance specification february 4, 2004 casi-N150P2-L06-fu01 32/34 14.0 packaging specification the packaging of the lcd meets 75 cm drop test. the following is the drawing of the package. www.datasheet.net/ datasheet pdf - http://www..co.kr/
customer?s acceptance specification february 4, 2004 casi-N150P2-L06-fu01 33/34 15.0 label there are labels on the rear side of the module. serial number label barcode character area www.datasheet.net/ datasheet pdf - http://www..co.kr/
customer?s acceptance specification february 4, 2004 casi-N150P2-L06-fu01 34/34 id label date label yy and ww of the week code stand for the year and the week of the year of manufacturing of the module respectively. ul label ****** end of page ****** www.datasheet.net/ datasheet pdf - http://www..co.kr/

▲Up To Search▲

Price & Availability of N150P2-L06

	To Download N150P2-L06 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .